Dip es SF is a ready-to-use teat disinfectant for use after milking in dairy cows. It is effective against bacteria and yeasts and should remain on the teats until the next milking.
Bring the product to a temperature above 20 °C before use. The use of a dosing pump is recommended for filling application equipment. Clean the teats immediately before milking by carefully wiping them with a disposable cloth/paper. After treatment, the animals should be allowed to stand for at least 5 minutes.
Cows: 5 ml per treatment (prepare per cow).
Fill the storage container with the ready-to-use product (prepare 5 ml per cow) and screw the dip cup onto the canister. Avoid the escape of excess liquid. After milking, squeeze the storage container and place the dip cup over each teat from below so that about 3 cm of the teat is immersed in the disinfectant. Refill the cup of the dip unit with fresh disinfectant if necessary and refill the reservoir as required.
Fill the storage container with the ready-to-use product (prepare 5 ml per cow) and screw on the spray gun. Avoid the escape of excess liquid. After milking, spray on the disinfectant so that about 3 cm of the teat canal is covered with disinfectant. Refill the reservoir if necessary.
Open a canister with the ready-to-use product (prepare 5 ml per cow) and insert the suction lance of the electronic sprayer. Avoid the escape of excess liquid. Spray onto the teats after milking, covering about 3 cm of the teat canal. Replace empty canisters if necessary. To clean the sprayer, place the suction lance system in a bucket of water and rinse the device by pumping water through it.
Open a canister with the ready-to-use product and insert the suction hose of the automated dipping system. After milking, the vacuum is switched off and the teat disinfectant is injected into a distributor on the claw piece. The teats are covered with approx. 5 ml of dip when the teat cup is removed using the automatic removal system. After each milking, the liners are thoroughly rinsed with water, blown out with compressed air and finally disinfected (e.g. with a product containing chlorine). The milking system is then ready for the next milking. The entire process is automated.
Open a canister with the ready-to-use product and insert the suction hose of the milking robot. The teats are cleaned by the robot with automatic brushes. After milking, the disinfectant is automatically sprayed onto the teats by a milking cluster arm. Leave the product on the teats until the next milking. Ensure that the animals remain standing for at least 5 minutes after treatment. The sprayer is rinsed automatically.
Detailed information on possible side effects and emergency measures can be found in the safety data sheet. Always have the product container or label ready in case of medical assistance.
Depending on local regulations, the used product can be flushed into the sewage system or disposed of in the slurry storage area; discharge to an individual sewage treatment plant should be avoided. Recommended cleaning agent: Water, cleaning agent if necessary.
Protect from frost and direct sunlight. The product may be stored at temperatures up to a maximum of 30 °C.
| Packung | 20 kg, 200 kg |
|---|---|
| Zulassungs-Nr. | EU-0018724-0008 1-7 |
| Inhaltsstoffe | 1400 ppm PVP iodine |
| Gefahrenhinweis-Sätze | H412: Harmful to aquatic organisms, with long-term effect. |
| Safety instructions | P101: If medical advice is required, Have packaging or identification label ready, P102: Keep out of the reach of children.n |
Arthur Schopf Hygiene GmbH & Co. KG
Pfaffensteinstr. 1
83115 Neubeuern
Germany
Telefon: + 49 8035 / 90260
Fax: + 49 8035 / 90260
info(at)schopf-hygiene.com
